Pirkšanas ceļveži

Which drill press?

Which drill press?

Short answer: Three bench drill presses, and the watts do not run in the same direction as the weight. The 500 W, model DP20013B, weighs 13.3 kg. The title says 203.2 mm. The drill is up to 13 mm. The spindle travel in the text is 50 mm. Five belt speeds are 500, 890, 1400, 1900 and 2500 revolutions. The 400 W, model DP25013B-VS, weighs 27.7 kg. The swing is 254 mm. The drill is also 13 mm. The travel is 60 mm. Its table has a rated power of 0.54 hp / 400 W and a separate row of 390 W. Both stay. The 550 W, model DP30016B-VS, weighs 42 kg. The swing is 305 mm. The drill is up to 16 mm. The travel is 90 mm. The rated power is 0.74 hp / 550 W. 750 W is not on any page. Voltage is not on any page.

Watts and drilling diameter do not travel together

The 13 mm maximum is on the 500 W page and on the 400 W page. The 16 mm maximum is only on the 550 W page. The 500 W does not drill a thicker hole than the 400 W. Both have a ceiling of 13 mm. More watts do not drill a thicker hole unless the page itself writes the larger diameter. The 500 W page writes 13 mm. The 400 W page writes 13 mm. Only the 550 W page writes 16 mm. The difference the pages actually give is the way the speed is set, the spindle travel, the weight, and whether the speed is changed with a belt or read from a digital display.

The 500 W text says a small radial runout, and it gives no number for that runout. The same text names an LED work light. The 400 W text and the 550 W text name an X-laser, which helps place the hole. The X-laser is not copied onto the 500 W page. The LED work light is not copied onto the 400 W page or the 550 W page. A runout number is not on any of the three pages, so none is added here.

The choice among these three is not a choice of 400 W or 750 W. 750 W is not written on DP20013B, not written on DP25013B-VS, and not written on DP30016B-VS. The three powers the pages do write are 500 W, 400 W with a separate 390 W row, and 550 W. A higher watt figure, taken by itself, does not move the 13 mm ceiling to 16 mm.

The 400 W page also has 390 W

The DP25013B-VS table says a rated power of 0.54 hp / 400 W, and the next row says a power of 390 W. The title says 400 W. The features say 400 W. The guide does not strike either row out. 390 W stays its own row, beside 0.54 hp / 400 W, and it is not folded into the 400 W line. The 550 W page is the clearer of the three on this point. The features say 550 W. The rated power says 0.74 hp / 550 W. The power row says 550 W. Those three writings agree. There is no second power figure on the 550 W page. The 500 W page says 500 W in the features and 500 W on the power row. A horsepower row exists only on the 400 W page and the 550 W page. The 500 W page has no horsepower row, and 0.54 hp and 0.74 hp are not written onto it.

Speed is not one scale shared by the three presses. The 500 W has five fixed belt steps: 500, 890, 1400, 1900 and 2500 revolutions per minute. The 400 W is variable, 440–2600, with a digital display. The 550 W is variable, 340–2200, with a digital display. 2600 is not on the 550 W page. 2500 is not on the 400 W page. 500, 890, 1400 and 1900 are the belt steps of the 500 W, and they are not written as the speed range of either digital press. A belt change is not written onto the digital pages. A digital display is not written onto the belt page. Each speed line stays on the page that prints it.

Swing and travel

203.2 mm is in the title of the 500 W page. The table on that page has no swing-distance row. What that table does have is the 13 mm drill, and what the text has is a spindle travel of 50 mm. 254 mm is in the table of the 400 W page, and the travel there is 60 mm. 305 mm is in the table of the 550 W page, and the travel there is 90 mm. The longer travel is on the heavier press. It is not on the lighter 500 W machine. 90 mm is not moved onto the 13.3 kg press, and 50 mm is not moved onto the 42 kg press.

The table tilts. The 500 W text says up to 45°, and it does not name a side. The 400 W text and the 550 W text say 45° to the left or to the right. The words “left or right” belong only to those two pages. Height can be adjusted on all three, which is what the pages say. No table gives the table’s own centimetres as a separate measure, so no table size in centimetres is added. Where the travel figure sits also stays put. On the 500 W page the 50 mm travel is in the text. On the 400 W page the 60 mm travel is in the table. On the 550 W page the 90 mm travel is in the table.

Weight and material

13.3 kg is the 500 W, and the box is 25 × 34 × 45 cm. 27.7 kg is the 400 W, and the box is 28.5 × 41 × 72 cm. 42 kg is the 550 W, and the box is 30 × 50.5 × 76.5 cm. The lower wattage is not the lighter press. The 400 W weighs more than twice the 500 W, and the pages give the reason as a different swing and a different body. 27.7 kg stays heavier than 13.3 kg. 42 kg stays the heaviest of the three. The box lines stay with the press they are printed under. They are not the swing, and they are not the spindle travel.

A material is written on only two pages. The 400 W page names Q235 and HT150. The 550 W page names Q235 and HT200. The 500 W page does not name a material. HT200 is not copied onto the 400 W page. HT150 is not copied onto the 550 W page. Q235 is not invented for the 500 W page. Voltage, a chuck taper and a column diameter are not on any page. They are not supplied from outside the pages. The missing voltage is not turned into 230 volts.

How to choose?

If the press has to be 13.3 kg, and the speed comes from five belt steps, that is DP20013B. The drill is 13 mm. The travel in the text is 50 mm. The light is an LED work light. There is no X-laser on this page. The title figure is 203.2 mm, and the table has no swing-distance row. The speeds are 500, 890, 1400, 1900 and 2500 revolutions per minute. This is the lightest of the three. It is not the press with the thicker hole.

If the wanted swing is 254 mm, and the wanted speed is the digital range 440–2600, that is DP25013B-VS. The page says 400 W and it also says 390 W. The rated-power row is 0.54 hp / 400 W. The next row is 390 W. The drill is still 13 mm. The weight is 27.7 kg, which is more than the 500 W press. The travel is 60 mm. The text names an X-laser and a tilt of 45° to the left or to the right. The material on this page is Q235 and HT150.

If the drill has to be up to 16 mm, and the travel has to be 90 mm, that is DP30016B-VS. The power writings on this page are 550 W, including the rated power 0.74 hp / 550 W. The swing in the table is 305 mm. The weight is 42 kg. The speed is the digital range 340–2200. This is the only page with 16 mm. The text names an X-laser, a tilt of 45° to the left or to the right, and the materials Q235 and HT200.

750 W is not in this guide. Voltage is not in this guide either. More watts do not turn the 13 mm drill of the 500 W or the 400 W into the 16 mm drill. That 16 mm line exists only where the 550 W page writes it. The 390 W row stays on the 400 W page as its own row.

Comparison

Product Price What sets it apart
Bench drill press 500 W, belt, 13.3 kg 182,90 € 5 belt speeds, LED, travel 50 mm, no material row
Bench drill press 400 W / 390 W, 254 mm 329,90 € digital 440–2600, X-laser, Q235 and HT150, travel 60 mm
Bench drill press 550 W, 305 mm, drill 16 mm 676,90 € digital 340–2200, X-laser, Q235 and HT200, travel 90 mm

The price in the link is the shop’s current price and opens the product.

Who is this not for?

  • 750 W is not on any page. The 400 W page has 400 W and a separate 390 W.
  • The 500 W does not drill a thicker hole than the 400 W. Both have a ceiling of 13 mm. 16 mm is only the 550 W.
  • The X-laser is not on the 500 W page. The LED is not on the other two.
  • Voltage is not on any page. It is not turned into 230 volts.

Frequently asked questions

Should you choose 400 W or 750 W?

There is no 750 W page here. The three pages are 500 W, 400 W with a separate row of 390 W, and 550 W.

Do more watts drill a thicker hole?

No. The ceiling on the 500 W and on the 400 W is 13 mm. 16 mm is only on the 550 W page. The 500 W is the lightest of the three, not the one with the thicker drill.

Why does the 400 W weigh more than the 500 W?

The page says 27.7 kg and a swing of 254 mm for the 400 W press, and 13.3 kg for the 500 W press, whose title is 203.2 mm. Watts are not the weight.

What is the 390 W row?

In the DP25013B-VS table the rated power is 0.54 hp / 400 W and the next row is 390 W. Both are on the page. Neither is struck out.

Does the 550 W page also have two power figures?

No. The features, the 0.74 hp / 550 W, and the power row all say 550 W. There is no second power there.

How is the speed changed?

The 500 W has five belt steps, 500 to 2500 revolutions. The 400 W is variable, 440–2600, with a digital display. The 550 W is variable, 340–2200, with a digital display.

Is there a laser on all of them?

The X-laser is in the 400 W text and the 550 W text. The 500 W text has an LED work light, not an X-laser.

How far does the spindle travel?

The 500 W text says 50 mm. The 400 W table says 60 mm. The 550 W table says 90 mm. Only the 500 W page names a depth stop in the text.

Does the table go to 45° both ways?

“Left or right” is in the 400 W text and the 550 W text. The 500 W says up to 45°, and it does not name a side.

What is the body made of?

The 400 W names Q235 and HT150. The 550 W names Q235 and HT200. The 500 W page does not name a material.

What is the voltage?

No page gives volts or hertz. That figure is not supplied from outside the pages.

How large is the swing?

The title is 203.2 mm on the 500 W page, and that page has no table row for it. 254 mm is in the 400 W table. 305 mm is in the 550 W table.

Is 13 mm the chuck?

The page states a maximum drilling diameter: 13 mm on the first two, 16 mm on the third. It does not name a chuck taper.

Which is the heaviest?

42 kg, model DP30016B-VS, 550 W, drill 16 mm, travel 90 mm. The lightest is 13.3 kg and 500 W.

Autors: mano.ee komanda. Cena ceļvedī ir veikala pašreizējā cena un ved uz preci. Piegāde parasti 4–10 dienas.